A1 Series Commercial Grade Meters - Flomec

 

• A025: (Low Flow)
• A100: (1 inch)
• A200: (2 inch)

• A025: Paddlewheel
• A100: Turbine
• A200: Turbine

• A025: 1 inch / NPT, ISO+ or BSPP (Female)
• A100: 1 inch / NPT, ISO+ or BSPP (Female)
• A200: 2 inch / NPT, ISO+

0,3 GPM(1 L/min) - 300 GPM(1135 L/min)

• A025: Application Dependent (see Note 1)
• A100, A200: ± 1.5%

• A025: ± 1.0%
• A100: ± 0.2%
• A200: ± 0.2%

300 psi (21 bar)

• -40° F to 250° F (-40° C to 121° C)
• with Safe Area Only Display: 0° F to 140° F (-18° C to 60° C)
• with Intrinsically Safe Display: 0° F to 129° F (-18° C to 54° C)

• A025: 2200 PPG (581 Pulses/L)
• A100: 730 PPG (193 Pulses/L)
• A200: 72 PPG (19 Pulses/L)

• A025: 11-110 Hz @ 0.3-3 GPM (1-11 L/min)
• A100: 36.5-608.3 Hz @ 3-50 GPM (11-190 L/min)
• A200: 36-360 Hz @ 30-300 GPM (114-1135 L/min)

• A025: 55 mesh (275 μm)
• A100: 28 mesh (700 μm)
• A200: 28 mesh (700 μm)

• Housing: Aluminum
• Bearings: Ceramic (96% Alumina)
• Shaft: Tungsten Carbide
• Rotor: Nylon
• Rings: 316 Stainless Steel

• Comes standard with A1 Series meters
• N.I.S.T. – Certification available.

Note 1: Accuracy can vary up to ± 5% depending on installation and fluid type. Field calibration is recommended for best accuracy

• N025: (Low Flow)
• N100: (1 inch)

• N025: Paddlewheel
• N100: Turbine

• N025: 1 inch / NPT, ISO+ or BSPP (Female)
• N100: 1 inch / NPT, ISO+ or BSPP (Female)

0,3 GPM(1 L/min) - 50 GPM(190 L/min)

• N025: Application Dependent (see Note 1)
• N100: ± 1.5%

• N025: ± 1.0%
• N100: ± 0.2%

150 psi (10.3 bar)

• -40° F to 250° F (-40° C to 121° C)
• with Safe Area Only Display: 0° F to 140° F (-18° C to 60° C)
• with Intrinsically Safe Display: 0° F to 129° F (-18° C to 54° C)

• N025: 2200 PPG (581 Pulses/L)
• N100: 730 PPG (193 Pulses/L)

• N025: 11-110 Hz @ 0.3-3 GPM (1-11 L/min)
• N100: 36.5-608.3 Hz @ 3-50 GPM (11-190 L/min)

• N025: 55 mesh (275 μm)
• N100: 28 mesh (700 μm)

• Housing: Nylon
• Bearings: Ceramic (96% Alumina)
• Shaft: Tungsten Carbide
• Rotor: Nylon
• Rings: 316 Stainless Steel

• Comes standard with A1 Series meters
• N.I.S.T. – Certification available.

Note 1: Accuracy can vary up to ± 5% depending on installation and fluid type. Field calibration is recommended for best accuracy

A1: A1 Series Turbine Meters 

Local Computer w/Display, Meter Mounted

• Q9: Q9 2-Button Computer 

Local Computer w/Display & Module, Meter Mounted

• P9: Q9 2-Button Computer w/Scaled Pulse Out Module, includes External Power and 10 ft. of Cable 934
• 42: Q9 2-Button Computer w/4-20mA Module, includes Scaled Pulse Out and 10 ft. of Cable

Module, meter mounted (No Display)

• PO: Pulse Out (unscaled) Conditioned Signal Module w/Cable

Retrofit Computer Kit (Display Only)

• R9: Q9 2-Button Computer Retrofit Kit (Replaces 09 Display)

No Electronics-Turbine Only

• XX: No Electronics-Turbine Only

• GM: Gallons Per Minute (For Use With Q9, Q1, R9 Electronics)
• LM: Liters Per Minute (For Use With Q9, Q1, R9 Electronics)
• XX: No Calibration (Use with XX Electronics Choice Only)

• A025: Aluminum - Low Flow 
• A100: Aluminum - 1 inch 
• A200: Aluminum - 2 inch 
• N025: Nylon - Low Flow 
• N100: Nylon - 1 inch 
• X###: No Turbine (Specify Turbine Housing size in place of the # # #).

• N: NPT (Female) 
• I: ISO Taper (Female) ISO 7
• B: BSPP (Female) (A025 & A100 models only) (ISO 228)
• X: No Turbin

With FM, ATEX & IEC Approval for HAZARDOUS AREA

• A1: Standard or Low Flow, 1 inch (w/Q9 & R9 Electronics Choice) 
• A2: Standard, 2 inch (w/Q9 & R9 Electronics Choice) 38
• B1: Standard or Low Flow, 1 inch Turbine Only 38
• B2: Standard, 2 inch Turbine Only 38
• B3: Display Only

Non-Approved Version - SAFE AREA ONLY

• C2: All Sizes with P9, 42, PO Electronics